Opens in a new tab

Length

Filter - Checkbox

    Width

    Filter - Checkbox

      Thickness

      Filter - Checkbox

        Colour Tone

        Filter - Checkbox

        Profile

        Filter - Checkbox

          Material

          Filter - Checkbox

          Fire Rating

          Filter - Checkbox

          Range

          Filter - Checkbox

          Species

          Filter - Checkbox

            Wood Type

            Filter - Checkbox

            Warranty

            Filter - Checkbox

              Moisture Content

              Filter - Checkbox

                Outdoor Screws

                Screws for outdoor timber, for fixing timber to timber and timber to masonry. For frames, battens and boards we stock C2 Exterior Strong-Fix wood screws, 5.0 mm with a PZ2 head, in 50, 80 and 100 mm lengths and coated for outdoor use. For fixing to concrete, brick, stone and block we stock a 7.5 mm TX30 concrete screw in 80 and 120 mm lengths that drives into a pilot hole without plugs. Stocked in our warehouse and delivered across Ireland.

                  Sort by

                  Showing 1-5 of 5 results

                  Screws for Outdoor Timber in Ireland

                  Every outdoor timber project is held together by two kinds of fixing: timber to timber, where one piece of the frame meets the next, and timber to masonry, where the frame meets a wall, slab or patio. We stock a screw for each, both made for outdoor use, so you can fix a deck frame, pergola, shed or garden room from the ground up.

                  Exterior wood screws

                  For timber to timber we stock the C2 Exterior Strong-Fix, a 5.0 mm screw with a PZ2 drive and a ribbed, double countersunk head that cuts its own countersink. A zinc base layer under a silver organic coating gives 1,000 hours of salt spray resistance, and the twin cut point starts quickly with less splitting. Pick the length by the timber you are fixing through:

                  • 5.0×50 mm, box of 200: 22 mm boards and battens to a frame.
                  • 5.0×80 mm, box of 200: 44 mm framing timber to timber, such as noggins, plates and joists.
                  • 5.0×100 mm, box of 100: 44 to 50 mm timber into posts and thicker members.

                  Concrete screws

                  For timber to masonry we stock a 7.5 mm concrete screw with a flat countersunk head and a TX30 Torx drive, in 80 mm and 120 mm lengths, packed in 100s. It drives straight into concrete, brick, stone or block through the timber you are fixing, so there are no nylon plugs to line up and no hammer fixings to knock home. Use the 80 mm screw for battens and brackets fixed tight to a wall, and the 120 mm screw for thicker ledgers and frames. The serrated, high low thread cuts its own path into the masonry, and an exterior plating resists 500 hours of salt spray testing.

                  Which screw for which job

                  Use the C2 wood screws wherever timber meets timber in a frame, and the concrete screws wherever timber meets a wall, slab or patio, such as a deck ledger on a house wall or a post holder on a patio. For decking boards, and for oak and cedar, whose tannins stain coated and mild steel, use stainless steel screws from our decking accessories. The C2 screws are rated 3 out of 5 for corrosion, so on coastal sites use stainless steel throughout.

                  Fixing tips

                  For the wood screws, drill a pilot hole near the end of a board and in hardwood; in most softwood the twin cut point drives without one. Drive with a PZ2 bit until the ribbed head sits flush. For the concrete screws, hold the timber in place, drill a pilot hole through it into the masonry, blow out the dust, then drive the screw with a TX30 bit until the head sits flush.

                  The screws pair with our cast iron post holders, concrete post bases and post connectors, and with framing timber such as our C24 timber. See the rest of our outdoor timber hardware for everything that goes with your posts and frames.

                  Frequently Asked Questions About Outdoor Screws

                  For timber to timber, such as framing, battens and boards, use the C2 Exterior Strong-Fix wood screws. For timber to concrete, brick, stone or block, use the concrete screws. For decking boards, oak and cedar, and coastal sites, use stainless steel screws from our decking accessories.

                  Pick it by the timber you are fixing through. Use 50 mm for 22 mm boards and battens, 80 mm for 44 mm framing timber, and 100 mm for fixing 44 to 50 mm timber into posts and thicker members.

                  They fix timber and hardware straight into concrete, brick, stone and block, replacing nylon plugs and hammer fixings. Use them to bolt down post holders, fix ledgers and battens to a wall, or fit window and door frames. They are 7.5 mm in 80 mm or 120 mm lengths, packed in 100s.

                  The C2 wood screws take a PZ2 Pozidriv bit. The concrete screws take a TX30 Torx bit, which reduces driver wear and stops the bit camming out.

                  Yes. The C2 wood screws have a zinc base under a silver organic coating with 1,000 hours of salt spray resistance, rated 3 out of 5 for corrosion. The concrete screws have an exterior plating that resists 500 hours of salt spray testing. On coastal sites, use stainless steel.

                  It has a two stage countersunk head, which reduces the chance of the head shearing off and helps it sit flush as it countersinks. Our C2 Exterior Strong-Fix wood screws and our stainless steel decking screws both have this head with ribs underneath.